Architectural Floor Plans (large)

Notes: 1/4' scale if possible - or 1/8" scale if 1/4" scale Plans are not necessary or would divide the Building into an excessive number of Sections

Checklist

  • Dimensions

    • Overall.
    • Column centers and designations.
    • Building breaks and set backs.
    • Masonry dimensions.
    • Dimensions from column centerline to exterior wall line.
    • Tie room dimensions into column centerlines.
    • Check Structural Plan dimensions with Architectural Plan dimensions.
    • Verify that interior dimensions add to yield overall.
    • Clarify as to exactly where a dimension starts and terminates.
    • Do not extend one dimension line through another - see "Graphic Symbol" Section.
    • Dimension finish wall to finish wall where necessary.

  • Room Designations

    • Name, Number.
    • References to large scale Details.

  • Finishes

    • Check Finish Schedule for each room for clarity.
    • When two finishes occur on floors, walls, etc., in an area, clearly define extent of each and how terminates if they converge.

  • Interior Walls and Partitions

    • Clearly define construction (new and existing).
    • Clearly define height.
    • Clearly define unusual items in Walls (insulation, sound deadening, rated walls, etc.)
    • Define which Partitions extend to structure above and how attached (parallel to structure - perpendicular to structure) (cell closures at metal deck, etc.).
    • Define Partition construction penetrated by Ductwork.
    • Dust Partitions
    • Verify Chase Wall thickness for Plumbing pipes.
    • Caution: If some Partitions extend through ceilings and some abut ceilings of a suspension system, wall angles of suspended grid should have a place to terminate.
    • Refer to example of "Clarification of Partition Designations" at the end of this portion.

  • Special Floor Patterns.

  • Mat Recesses.
  • Change in Materials.
  • Ramps.
  • Curbs, Bases, and Gutters.
  • Material indications.
  • Pipe and Duct spaces.
  • Recessed Heaters and Convectors.

  • Recessed or surface mounted Electrical Panels. Drinking Fountains (DF) or Electrical Water Coolers (EWC).

  • Ceilings

    • Indicate changes in height of ceilings (dashed line).
    • Skylights (dashed line).
    • Roof hatches ( dashed line).
    • Cubicle tracks (dashed line).

  • Floor Drains

    • Indicate and Coordinate with Mechanical

  • Doors

    • Swing and "Door or Opening Designation."
    • Hardware Set indicated.
    • Folding Doors, etc.
    • Show Thresholds.
    • Coordinate door swings with location of electrical light fixture switches shown on Lightning Plans.
    • Check door swings into means of egress.

  • Windows and Exterior Louvers

    • Mullions
    • Type Designation
    • Masonry Opening

  • Toilet Rooms

    • Plumbing Fixtures.
    • Toilet Partitions and Urinal Screens with dimensions.
    • Floor Drains.
    • Reference to large scale Details or Plan. Shower head locations.
    • Curbs.
    • Toilet Room accessories (if not shown elsewhere).

  • Stairs

    • Number each Stair.
    • Dimension Wall.
    • Show traffic direction.
    • Indicate number of risers.
    • Handrails.

  • References

    • Exterior Wall Sections (vertical).
    • Horizontal Sections and Enlargements.
    • Reference Structural, Mechanical, and Electrical Sheets where useful.

  • Miscellaneous

    • Fire extinguishers and/or cabinets (check Partition thickness to facilitate recessed cabinet- approximately 7-1/2" required).
    • Access Doors.
    • Expansion Joints.
    • Folding Partitions.
    • Ladders.
    • Pits and Gratings.
    • Lockers and Benches.
    • Millwork with references to Details.
    • Corner Stones.
    • Plaque
    • Corner Guards.
    • Telephone Booths.
    • Check and show location of roof leaders from roof drain
    • Check location of Vent Pipes, Hot Water Heater Flues, Boiler Flues, etc.
    • Chalk and Tack Boards.
    • Building Directory location.
    • Folding Gates.
    • Railings.
    • Trophy Cases.
    • Casework.
    • Laboratory Equipment.
    • Major Mechanical and Electrical Equipment
    • Direction of Seams for sheet vinyl flooring
    • Expansion Joints.
    • Folding or Coiling Grilles.
    • Kitchen Equipment.
    • Location of Key Cabinet when specific under "Hardware."
    • Indication of North.
    • "Drawing Title Designation."
    • Column Reference Grid
    • If possible, orientate Site Plan, all Floor Plans, partial or enlargement Plans (stairs,elevators, equipment rooms, food service) in the same relation to North on all Drawing Sheets.)
    • Key Plans where necessary - Key Plans should include the image of the Building for each floor or level, as letter designation for each Section the Building is divided into, each level noted, indication of North and "Key Plan" noted.

results matching ""

    No results matching ""